Neck Finish Specifications for Child Resistant Closures for SPI-400 Finishes, Except as Noted
| Option 1 = Closure Diameter Larger Than Bead |
Option 2 = Closure Diameter Smaller Than Bead/Shoulder |
||
CLOSURES |
MM |
“H” Minimum |
“H1″ Minimum |
| Rexam | |||
| FG | 20 | 0.349 | 0.442 |
| 22 | 0.349 | 0.442 | |
| 24 | 0.378 | 0.436 | |
| 28 | 0.378 | 0.436 | |
| 410 finish | 28 | 0.565 | 0.581 |
|
480 finish
|
33 | 0.378 | 0.439 |
| 38 | 0.378 | 0.427 | |
| 45 | 0.378 | 0.448 | |
| Clic-Loc | 20 | 0.349 | 0.389 |
| 22 | 0.349 | 0.389 | |
| 24 | 0.378 | 0.418 | |
| 28 | 0.378 | 0.418 | |
| 480 finish | 28 | 0.565 | 0.605 |
| 33 | 0.378 | 0.418 | |
| 38 | 0.378 | 0.418 | |
| 45 | 0.378 | 0.418 | |
| Argus-Loc | 24 | 0.378 | 0.495 |
| 28 | 0.378 | 0.495 | |
| 33 | 0.378 | 0.495 | |
| 38 | 0.378 | 0.495 | |
| Chem-Loc | 28 | 0.378 | 0.495 |
| 33 | 0.378 | 0.495 | |
| 38 | 0.378 | 0.495 | |
| Berry Kerr | |||
| CR-I | 20 | 0.349 | 0.466 |
| 22 | 0.349 | 0.466 | |
| SD-350 finish | 22 | 0.455 | 0.513 |
| 24 | 0.378 | 0.495 | |
| SD-350 finish | 24 | 0.485 | 0.543 |
| 28 | 0.386 | 0.525 | |
| 480 finish | 28 | 0.565 | 0.631 |
| 33 | 0.378 | 0.495 | |
| 38 | 0.378 | 0.495 | |
| 45 | 0.378 | 0.495 | |
| Gutman | |||
| Saf-Lok | 24 | 0.378 | 0.450 |
| 28 | 0.378 | 0.500 | |
| 33 | 0.378 | 0.500 | |
| 38 | 0.378 | 0.500 | |
| 45 | 0.378 | 0.500 | |
| Mold-Rite | |||
| 24 | 0.400 | 0.530 | |
| 28 | 0.400 | 0.530 | |
| 33 | 0.403 | 0.533 | |
| 38 | 0.403 | 0.533 | |
| 45 | 0.403 | 0.533 | |
| MAC | |||
| 24 | 0.378 | 0.405 | |
| 28 | 0.378 | 0.405 | |
| 33 | 0.378 | 0.405 | |
| 38 | 0.378 | 0.405 | |
| Plastic Bottle Corporation | 22 | 0.356 | 0.356. |
| Van Blarcom | |||||
| Option 1 Closure Diameter Large Than Bead |
Option 2 Closure Diameter Smal Than Bead or Shoulder |
||||
CLOSURES |
“H” Min |
“B” Max |
“D” Min |
“H” Min |
|
Bead |
Shoulder |
||||
| Saf-Cap I | 20mm | .356 | .860 | .510 | |
| 22mm | .356 | .915 | .510 | ||
| 24mm | .410 | 1.030 | .565 | ||
| 28mm | .425 | 1.175 | .575 | ||
| 33mm | .425 | 1.365 | .575 | ||
| 38mm | .425 | 1.575 | .575 | ||
| 45mm | .425 | 1.800 | .610 | ||
| 53mm | .435 | 2.150 | .610 | ||
| Saf-Cap II | 28mm | .425 | 1.130 | .540 | |
| 38mm | .425 | 1.510 | .540 | ||
| Saf-Cap III | 24mm | .340 | 1.000 | .475 | |
| 28mm | .340 | 1.150 | .475 | ||
| 33mm | .340 | 1.340 | .475 | ||
| 28mm | .340 | 1.540 | .475 | ||
| 45mm | .340 | 1.780 | .475 | ||
| Saf-Cap III-A | 20mm | .360 | .830 | .500 | |
| 24mm | .425 | 1.010 | .570 | ||
| 28mm | .425 | 1.165 | .570 | ||
| 33mm | .425 | 1.340 | .570 | ||
| 38mm | .425 | 1.540 | .570 | ||
| 45mm | .425 | 1.795 | .570 | ||
| 53mm | .435 | 2.150 | .610 | ||
The above information is offered as a general guideline only; we cannot guarantee its accuracy. You must check directly with your closure manufacturer for the required “H” dimension and any other required specifications. A more complete chart is available in our catalog.
